rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (4) stand juni 2016 rev 01 dc/dc-converter rs5-r30w/rd30w 3.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! ? 8 pin sil package ? wide 4:1 input range ? 1600vdc isolaton ? contnuous short circuit protecton ? efciency up to 82% ? operatng temperature range -40 ~ +85c ? non conductve black plastc case ? remote on/of control(optonal) output specification voltage accuracy: 1% maximum output current: see table line regulaton: 0.2% max. load regulation: single (from 0% to 100% load) 1% max dual (from 10% to 100% load) 1% max cross regulaton (dual output): 5% short circuit protecton : indefnite (automatc recovery ) ripple noise (20mhz bandwidth): 30mv pk-pk max. temperature coefcient: 0.02%<>c capacitor load: see table transient recovery time: 250us, typ. transient response: ( deviaton) 3% max. input specifications voltage range: see table start up time: 30ms, typ. max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20ma pk-pk general specifications efciency: see table i/o isolaton voltage (60sec): 1600vdc i/o isolaton capacitance: 200pf max. i/o isolaton resistance: 1000m ohm, min switching frequency: 250khz, typ. humidity: 95% rel h reliability calculated mtbf : > 1.7mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 remote on controll: on: 0 open or high impedance remote of controll: of: 2-4ma input current (via 1k) of stand by current (nominal vin): 2.5ma max. environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non conductve black plastc pin material sip case: c519r-h solder -coated potng material: silicon (ul94v-0 rated) weight case- sip: 4.8g, typ. dimmension sip: 0.86 x 0.36 x 0.44 absolute maximum ratings input surge voltage (100ms)/ 12 v models: 25vdc max. 12v models: 50vdc max. 48v models: 100vdc max. soldering temperature: 260c max. (2) emc specifications radiated-/conducted emissions: en55022 class a (see emi filter note) esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (4) stand juni 2016 rev 01 model selection guide model number input voltage range input current output voltage (vdc) output current efficiency @fl(%) c apa c i t o r no - load (ma) full load (ma) min. load (ma) full load (ma) rs5 - 1 2 03 r30a1w 4.5 - 18 40 268 3.3 0 700 72 1760uf rs5 - 1205 r30a1w 4.5 - 18 40 325 5 0 600 77 1000uf rs5 - 1212 r30a1w 4.5 - 18 40 309 12 0 250 81 170uf rs5 - 1215 r30a1w 4.5 - 18 40 309 15 0 200 81 110uf rs5 - 1 205 rd30a1w 4.5 - 18 40 325 5 0 300 77 470uf rs5 - 1 212 rd30a1w 4.5 - 18 40 313 1 2 0 125 80 100uf rs5 - 1 215 rd30a1w 4.5 - 18 40 313 1 5 0 100 80 47uf rs5 - 2 4 03 r30a1w 9 - 36 25 129 3.3 0 700 75 1760uf rs5 - 2405 r30a1w 9 - 36 25 159 5 0 600 79 1000uf rs5 - 2412 r30a1w 9 - 36 30 153 12 0 250 82 170uf rs5 - 2415 r30a1w 9 - 36 30 153 15 0 200 82 110uf rs5 - 2 405 rd30a1w 9 - 36 30 159 5 0 300 79 470uf rs5 - 2 412 rd30a1w 9 - 36 35 159 1 2 0 125 79 100uf rs5 - 2 415 rd30a1w 9 - 36 35 157 1 5 0 100 80 47uf rs5 - 4 8 03 r30a1w 18- 75 15 6 6 3.3 0 700 74 1760uf rs5 - 4805 r30a1w 18- 75 15 8 1 5 0 600 78 1000uf rs5 - 4812 r30a1w 18- 75 15 7 9 12 0 250 80 170uf rs5 - 4815 r30a1w 18- 75 15 7 8 15 0 200 81 110uf rs5 - 4 805 rd30a1w 18- 75 15 8 0 5 0 300 79 470uf rs5 - 4 812 rd30a1w 18- 75 15 8 0 1 2 0 125 79 100uf rs5 - 4 815 rd30a1w 18- 75 15 8 0 1 5 0 100 79 47uf note the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@ rsg - electronic.de 1. one load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within 5%. 2. measured with a 1uf ceramic capacitor. 3. test by minimal vin and constant resistive load. 4. test by normal vin and 100% - 25% load,25% ioad step change. 5. measured input reflected ripple current with a simulated source inductance of 12uh and a source capacitor cin(47uf, esr<1.0 at 100khz) . 6. exceeding the absolute ratings of the unit could cause damage. it's not allowed for continuous operating ratings. 7. input filter components are be required to help meet conducted emission class a, which application refer to the emi filter of design & feature configura tion. 8. an external filter capacitor is required if the module has to meet iec61000 - 4 - 4 and iec61000 - 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v. dc/dc-converter -/d ete ne d tt we energize electronics! an acal group company we energize electronics! r s 5 - xx xx x x xx p ower (w) input t ype a x w code inter nal isolation (kvdc) w = 4:1 input range model selection guide model number input voltage range input current output voltage (vdc) output current efficiency @fl(%) c apa c i t o r no - load (ma) full load (ma) min. load (ma) full load (ma) rs5 - 1 2 03 r30a1w 4.5 - 18 40 268 3.3 0 700 72 1760uf rs5 - 1205 r30a1w 4.5 - 18 40 325 5 0 600 77 1000uf rs5 - 1212 r30a1w 4.5 - 18 40 309 12 0 250 81 170uf rs5 - 1215 r30a1w 4.5 - 18 40 309 15 0 200 81 110uf rs5 - 1 205 rd30a1w 4.5 - 18 40 325 5 0 300 77 470uf rs5 - 1 212 rd30a1w 4.5 - 18 40 313 1 2 0 125 80 100uf rs5 - 1 215 rd30a1w 4.5 - 18 40 313 1 5 0 100 80 47uf rs5 - 2 4 03 r30a1w 9 - 36 25 129 3.3 0 700 75 1760uf rs5 - 2405 r30a1w 9 - 36 25 159 5 0 600 79 1000uf rs5 - 2412 r30a1w 9 - 36 30 153 12 0 250 82 170uf rs5 - 2415 r30a1w 9 - 36 30 153 15 0 200 82 110uf rs5 - 2 405 rd30a1w 9 - 36 30 159 5 0 300 79 470uf rs5 - 2 412 rd30a1w 9 - 36 35 159 1 2 0 125 79 100uf rs5 - 2 415 rd30a1w 9 - 36 35 157 1 5 0 100 80 47uf rs5 - 4 8 03 r30a1w 18- 75 15 6 6 3.3 0 700 74 1760uf rs5 - 4805 r30a1w 18- 75 15 8 1 5 0 600 78 1000uf rs5 - 4812 r30a1w 18- 75 15 7 9 12 0 250 80 170uf rs5 - 4815 r30a1w 18- 75 15 7 8 15 0 200 81 110uf rs5 - 4 805 rd30a1w 18- 75 15 8 0 5 0 300 79 470uf rs5 - 4 812 rd30a1w 18- 75 15 8 0 1 2 0 125 79 100uf rs5 - 4 815 rd30a1w 18- 75 15 8 0 1 5 0 100 79 47uf note the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@ rsg - electronic.de 1. one load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within 5%. 2. measured with a 1uf ceramic capacitor. 3. test by minimal vin and constant resistive load. 4. test by normal vin and 100% - 25% load,25% ioad step change. 5. measured input reflected ripple current with a simulated source inductance of 12uh and a source capacitor cin(47uf, esr<1.0 at 100khz) . 6. exceeding the absolute ratings of the unit could cause damage. it's not allowed for continuous operating ratings. 7. input filter components are be required to help meet conducted emission class a, which application refer to the emi filter of design & feature configura tion. 8. an external filter capacitor is required if the module has to meet iec61000 - 4 - 4 and iec61000 - 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v.
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (4) stand juni 2016 rev 01 efficiency vs output current 8 0 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 20% 40% 60% 80% 100% load lo line/iin nominal/iin hi line/iin efficiency vs output current 90 80 70 60 50 40 30 20 10 0 20% 40% 60% load nominal/iin 80% 100% lo line/iin hi line/iin input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test use a capacitor cout(1.0uf) measurement. the scope measurement bandwidth is 0 - 20mhz. +vout single dc/dc converter copper strip 1uf cout scope resistive load - vout +vin l +vout emi filter input filter components (c1, l) are used to help dc/dc c1 converter load meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. - vin - vout rs5 - 1203r30a1w rs5 - 4815r30a1w the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@ rs g - electronic.de +vout +vin lin current probe cin dc/dc converter load - vin - vout c1 l rs5 - 12xxr/rd30a1w 1210 10uf/35v 2 .5uh rs5 - 24xxr/rd30a1w 1210 2.2uf/100v 10uh rs5 - 48xxr/rd30a1w 1210 2.2uf/100v 18uh ffcc vs crr 8 0 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 20% 40% 60% 80% 100% load lo line/iin nominal/iin hi line/iin efficiency vs output current 90 80 70 60 50 40 30 20 10 0 20% 40% 60% load nominal/iin 80% 100% lo line/iin hi line/iin input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. output ripple & noise measurement test use a capacitor cout(1.0uf) measurement. the scope measurement bandwidth is 0 - 20mhz. +vout single dc/dc converter copper strip 1uf cout scope resistive load - vout +vin l +vout emi filter input filter components (c1, l) are used to help dc/dc c1 converter load meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. - vin - vout rs5 - 1203r30a1w rs5 - 4815r30a1w the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in s h o r t f o r m c o v e r o r e - m a i l t o : info@ rs g - electronic.de +vout +vin lin current probe cin dc/dc converter load - vin - vout c1 l rs5 - 12xxr/rd30a1w 1210 10uf/35v 2 .5uh rs5 - 24xxr/rd30a1w 1210 2.2uf/100v 10uh rs5 - 48xxr/rd30a1w 1210 2.2uf/100v 18uh dc/dc-converter rs5-r30w/rd30w 3.0w regulated single & dual output we energize electronics! an acal group company we energize electronics!
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (4) stand juni 2016 rev 01 rs5-xxxxr30a1w rs5-xxxxr30a1w dc/dc-converter rs5-r30w/rd30w 3.0w regulated single & dual output we energize electronics! an acal group company we energize electronics! mechanical specifications the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
